New Amp: Marshall JCM800 Model 2203x Reissue

I finally have a single channel, master volume, Super Lead Mark II amp. The full 100 watter too, and a reissue to boot.

This is a hell of an amp, and I can see why this has been the tone people lust after for years, build amps based around, modify to their liking, and so on. This amp is dynamic, punchy, full sounding, and has this incredible elasticity and flow to the notes that is impossible to really describe without experiencing.

There’s not much to cover since it’s such a simple design, based on the early plexi circuits but using cascaded gain stages (and the voicing shaped to accommodate that), the JCM800 2203 is a staple of modern rock tones and possible the most famous and most recorded amp of all time (for overdriven tones, at least). A simple front panel has six knobs - presence, treble, mids, bass, volume, and preamp gain. Two inputs, a high and a low (skips one of the three gain stages). These are invariably run with the preamp gain set to max, but if desired can be set lower for surprisingly great sounding clean tones. Compared to the split channel JCM800s I have, this one feels like the mids are a little more relaxed, the amp just a tiny bit more mild, but with an even wider spectrum of sound. Contrasting with the JVM410 I got around the same time, this amp is the total opposite - it’s extremely touch sensitive and has very present ultra-highs, but without being piercing, and deep full lows that extend beyond any lows coming out of the JVM.

This particular unit is a 2005 reissue, complete with a factory effects loop, but still sporting the silver back grille (as opposed to modern Marshall’s black).

No other features on this one - just one great channel, a nice loop, and some of the best rock tones I’ve ever heard. Also no surprise that this is one of the best pedal platforms out there, it can be taken into extreme metal territory with a boost or distortion pedal and all of the characteristics of the pedal shine through as well, enhanced and colored by the amp perfectly. I have had a Joyo Ultimate Drive (OCD clone) for years now and thought it was awful until I heard it through this amp. My SD-1 and Tubescreamers sound great as well, and I can imagine any unique overdrives would have their full potential realized through an amp like this one.

Definitely a long term keeper - and it looks great stacked on top of my JCM800 2210 and JCM800 1960A cabinet!

New Amp: Marshall JVM410H

Since I’m going through the whole range of Marshall amps anyway, I knew I’d have to try the JVM eventually. I never got the appeal of the 2 channel models, so when this four channel popped up for around the same price I went for it.

I’ve heard these compared to JCM800’s, supposedly sharing the same power amp design and similar topology in the 3-gain stage mods of the crunch channel, or green mode of OD1.

Well I have to report that is not at all the case. The JVM is definitely a versatile amp with some great tones, but it is no JCM800 replacement, at least not for me, and not even close to replacing my split channel 800s.

OD1 is very close sounding to my TSL head, nearly identical in fact, but more congested than that amp. Something about the overdrive channels of the JVM is that all of the frequencies seem to be condensed a little to a more focused spectrum - it has less deep bass and less “air” highs than the TSL, or my JCM800’s. On top of that, this amp has as much gain as the TSL has at max around 1 O’clock, but it also has far more background noise - and I’d never call the TSL a “quiet” amp. I’m not sure why they decided to do this, I’d think a smoother taper on the gain controls would be much more usable.

OD2 can get a pretty close to rectifier tone, but with a squishier, more saturated attack to the bass notes. I’m not the biggest fan because the same issue with the focused frequency spectrum means I preferred my actual rectifiers, but I can see how a JVM410 would be a killer amp for a cover band - you could do 80s metal on OD1 right up to Nu-metal recto tones on OD2 all with a couple of taps on the footswitch.

My favorite mode on this amp is Clean Red, which oddly uses all 4 gain stages but stays just a tad overdriven and clear. I find this mode to be the most similar to my Plexi’s normal channel, which is funny because my actual Plexi uses only 2 gain stages.

Crunch felt a bit underwhelming as well, it just doesn’t have the punch of… flow? of the JCM800’s. A certain je ne sais quoi that the 800’s have that this amp does not on any mode. Again, red mode was my favorite here.

I can compliment the digital reverb, which was very close to my TSL’s real spring reverb when A/Bing these amps. The TSL was just a tiny bit bouncier on the clean tones, for example playing surf style music, but for most tones and especially on distortion channels to add some weight it was functionally identical.

With so many other fantastic Marshalls in my collection, and no plans to ever drop down to only one or two amps ever again, I’m not sure where this amp fits in. I think this is another one to be returned - but it was fun to try out for a little while.

Grab one on Reverb here: Marshall JVM on Reverb

New Video: Orange Thunderverb vs Rockerverb vs Dual Dark comparison

Put together some comparison clips playing some heavy riffs through all three of these amps. They all have that strong Orange midrange but quite a few differences in overall gain and voicing, especially noticeable in the top end.

I’m not sure which one is my favorite - probably the Thunderverb Channel A for me.

New Video: Orange Dual Dark 50

I just put together this video showcasing some of the details, features, and tones this awesome metal amp can produce. Too bad these are discontinued, and hard to find at that! I searched a long time to get a hold of this one and it was well worth it.

New Video: Charvel Model 3A

Similarly to my BC Rich ST-III video, this guitar is now off to its new owner! Nothing like selling a guitar off that I will most likely never see again to put the pressure on to make a video!

I got this guitar years ago and it’s in truly superb condition. It was dusty and the truss cover still had the plastic on it! I imagine this guitar spent a lot of time sitting in someone’s closet or under the bed. I lowered the action a bit and really enjoyed playing it. The pickups are some of my favorites in the range and I find them to be very dynamic especially when paired with an amp without much compression.

New Amp: Marshall JCM800 Model 2210 Split Channel

I put in this order as soon as I saw the listing pop up on Guitar Center’s used listings. It was listed as a 2203x Reissue, which I’ve really wanted for a while, and the price was about half the going rate for one of those. The store called me to tell me that it was no a 2203, but instead a 2210 model. I verified the serial number was from 1986, making it likely to have the later version of the circuit like my beloved 2205, so I went for it anyway and figured worst case scenario it’d be an easy flip for a profit.

Disappointingly, the amp arrived with some serious damage to the headshell, with the top piece of wood with the handle cracked and splitting from the vertical sides at the finger joints. It tore the tolex there and was only held together by the rivets of the plastic corner pieces. On top of that, the spring reverb tank was totally trashed, the springs inside broken so badly they actually damaged the transducers inside as well beyond repair. Luckily, the amp itself worked and it even came with a nice set of SED Winged =C= EL34 power tubes (which I immediately removed and packaged away for later use).

I gave the store a call and they were very understanding and able to work out a partial refund deal for me. That should cover the cost of either a headshell repair/replacement and the spring reverb tank, though I’ll have to do the work myself, but that’s okay.

This amp is a blast though - it sounds incredible. Very interesting to me, but when it arrived I immediately set the controls exactly the same as my 2205. However, this 2210 sounds quite different - it’s much less bright, a bit thicker sounding with stronger lower mids. Both amps still excel at what they set out to do, and share the same core tone and feel, but it is interesting that my 2205 with the treble on “3” is about the same as this amp with the treble nearer to “7.”

Probably the hardest part about that now is it’s so hard to decide which of these two amps to keep. I thought this would be a slam dunk - sell the 100 watter since it’s louder, but now I’m finding it just as easy to dial in at studio volumes and has a different tone altogether. I’ll have to open them both up and see if any modifications have been performed. I suspect this 2210 has at least some upgrades done, since during this time it should’ve been equipped with 6550/KT88 power tubes (and my 2205 has a pair of these), but instead came with EL34’s and runs just fine with those tubes.

Still, deciding between two fantastic sounding JCM800’s is a good problem to have.

New Amp: Mesa Boogie Mark V

I’m about ten years late to the party on this one, so there’s not much I can say that hasn’t been said before. But after owning a Mark IV for a couple of years and loving it, I finally picked up a Mark V. Is it better than the IV? In some ways, definitely. In others, maybe not - but barely.

How is it better? Well for one, the spring reverb actually works and sounds great. My Mark IV as soon as you turn the reverb above “0,” the drive channels instantly lose a ton of bass and fullness, and sound tinny. At first, I thought there was something wrong with my IV, but turns out that’s just expected behavior for them. Since the Reverb isn’t footswitchable, in my mind it may as well not even be there. The V corrects this problem on both fronts - reverb can be turned on and off via footswitch, dialed in different amounts of each of the 3 channels, and it sounds amazing with a nice long tail and doesn’t affect the core tone of any channel at all.

Other great features are 3 modes per channel, some of which are a little better than others but that’s the point - nearly anyone’s preferences are catered to in this amp. I find channel 1’s clean to be almost identical to the Mark IV’s RHY 1 channel, but with a more usable EQ. The Mark V also adds a fat and tweed mode to this channel, expanding the range quite a bit and can even double as a light crunch channel in tweed mode.

Channel 2 offers Edge, Crunch, and Mark I modes… the standout to me here is the Mark I mode by far. With the gain and treble maxed out, the Mark I mode could be a high gain amp all on its own. This is one of the best tones I’ve had from any amp really, and I’d even be happy if this was the only channel/mode of an entire amp! It’s much darker than your usual Mark tone, though it can get lost in the mix a little and probably isn’t the best pairing for lower tunings. Keep the treble maxed just like you would on a real Mark I or it becomes very dull and muddy. This is Fender EQ topology, remember.

Channel 3’s Mark IIC mode gets a lot of praise, but I’ve grown fond of my Mark IV, so I jump straight into IV mode. It is an excellent recreation - side by side nearly identical to my Mark IV the way I have it dialed. On my IV, I set my gain and drive to 8, and treble to max. On the V, I set the gain to about 7-8, treble maxed, so I’m not surprised they sound so close. However, the Mark IV does have a couple of controls that the V doesn’t have, and if you really use those then you might be disappointed by the V. For example, the IV has both a gain control and a “lead drive” control, which can be dialed in differently for some variety on the tone. I personally like them both set exactly the same, which is how the V works, but if you like lower gain and higher drive, or vice versa, you can’t get that same tone out of the V. Another missing features is the “harmonics” or “mid gain” switch of the IV, which changes the voicing of the amp. The V feels to me like it’s based on the “harmonics” voicing, which is the most popular voicing I’m sure, but if you like the “mid gain” voicing it isn’t here. And last thing, the IV has “shift” controls on the presence pull pots, which drastically changes the way the attack of the notes sounds and feels. I like to use the shift function on RHY 2 of the IV to liven it up, the V does not have this voicing at all.

One other issue with the V so far, on the IV I had a six button footswitch - the first four buttons being RHY 1, RHY 2, Lead, and Lead +EQ. I liked being able to jump from Lead to Lead+EQ directly from the footswitch without tap dancing, and the volume levels were pretty close on that channel. On the V, engaging the EQ on Channel 3 results in a HUGE volume boost, so much so that you either have to press both the “EQ” and “CH 3” buttons at the same time with your foot, or as I’ve done, just set it so that Channel 3 has the EQ “always on” and dial the master to match channels 1 and 2. It’s really a minor complaint, but I do feel like that’s the only way to use it - maybe if there were a total volume control as part of the graphic EQ, kind of like how MXR EQ footpedals are - that could balance the volumes a little better. Anyway, those are my only complaints and overall it’s a superior amp to the Mark IV as long as you are using multiple modes. If you live and breathe on the IV’s lead channel, I think the IV has the superior lead channel and offers a few cool features that the V doesn’t have.

More Details Here

New Video: BC Rich ST III

Just before I sent my ice blue ST-III off to its new owner this week, I put together this video to showcase its features and quirks. I’ll definitely miss this guitar, it has a really fantastic neck and it was in great condition for its age. The Ibanez Edge trem is one of my favorites and it was cool to have that bridge on a guitar that wasn’t an actual Ibanez too.

My plan is to make videos for every guitar and amp I have, so I have a lot of material to work on, so subscribe to my youtube channel! I’ll do my best to put out a video every week or two. Enjoy!

New Amp: Blackstar HT-100 Stage

This is another amp from my early days of playing that I haven’t had the chance to try out in almost a decade. While looking for some small parts in my local Sam Ash, I spotted this head tucked away in a corner for a very reasonable price (and always nice to buy locally - no shipping costs).

Since I was so disappointed by the Egnater Renegade, and already owned the Marshall JCM800 I thought would cover the same ground as this amp, I decided I should really play it to find out if it’s as good as I remembered.

Well, it’s definitely no slouch! I remember only being interested in the HT-100 and HT-60 models back then, because the HT-40 and smaller models did not have the crunch channel (OD1). That channel alone is really great - and both OD1 and OD2 channels have a “voicing” switch that adds a lot of brightness and it feels like a little gain too. I think OD1 with the voicing switch out is a really great classic rock tone, pop on the voicing switch and the brightness really kicks in and it gets a bit more modern and grittier. OD2 is fantastic through and through, even if lacking a little clarity on top, adding the voicing switch brings some of that back in.

The digital reverb is very nice quality, and the ISF control seems less useful than I remember but it is still a cool feature to combine with the traditional 3-band EQ. I find there is one area where I think it sounds best for all channels, but for recording purposes the ISF can be used to dial in a pretty wide variety of tones, as long as you also adjust the 3-band to compensate appropriately.

These amps have a classic Marshall type design of 3 preamp tubes, and in this case 4x EL34 power tubes. The Mark II version of this amp only has 2 preamp tubes, so I’m not sure why kind of magic is going on there - tube gain stages replaced by transistors, or PI converted to solid state etc., but I’m happy with this 3-tube setup. It’s very difficult to find concrete answers as to the signal path of this amp, and now it’s been a whole decade since they were so popular it’ll probably be tough to really find out. I did find a schematic but this one is a bit more complicated than I’m used to, with a lot of op-amps and other things I haven’t learned the functions of yet, but a cursory glance shows a couple of tube gain stages and a few diodes, but I’m not sure if the diodes are used for overdrive or not. If I find out, I will update this post.

Op-amps, diodes, or not, it’s a great sounding amp and deceptively good - I paid under $400 for this amp and I feel it holds up very well to amps that cost 3x or 4x its price. A winner for sure - and no surprise these were all the rage when they came out, and why the HT5 and HT20 models still sell well today.

New Amp: Steavens Poundcake 25th Anniversary

Saw this and after reading some reviews and listening to clips of earlier Steavens amps online, I was very interested in an amp that seemed right up my alley.

See here for many more photos and details: Steavens Poundcake 25th Gallery

This is a heck of an amp - very nicely constructed, large, and heavy with huge transformers. The programmable footswitch allows memory access to some rudimentary “patch” settings for each of the 4 channels. Each channel has three modes (green, yellow, red), a mid boost, either of two master volume controls, and a switchable effects loop (all footswitchable and stored on a patch, each channel can store two different combinations of settings). The 3 overdrive channels also have a physical bright switch (not footswitchable).

The combinations of modes and the mid boost can really vary the tones from the amp, and it has a killer core tone already. The crunch channel is excellent and Meat and Heat channels are fairly interchangeable. My only major complaint is that the clean channel has a separate EQ and volume control, but all 3 overdrive channels share the same EQ and volume controls. Each has its own gain control however, and the volumes are pretty well balanced even at different gain settings so it’s not all bad. It’d just be nice to dial in a scooped high gain sound, and a mid boosted high gain sound with the EQ and be able to footswitch between them, but that’s not possible. In fact, the “mid boost” feature actually accentuates upper frequencies so in practice I’m using the mid boost for my rhythm tone and leave it turned off for fuller sounding lead sounds.

A previous owner modified this amp by adding another rotary selector on the back to change speaker cabinet impedance. I’m not sure why the stock switch wasn’t acceptable, the new one is identical to the old one but is just physically larger - and two new holes drilled in the chassis to mount it. Seems like kind of a stupid thing to do to me but maybe there was a good reason that’s now lost to time.

A great sounding amp overall and certainly one of the more unique amps in my collection.